Number of the records: 1
Vliv tepelného zpracování a modifikace antimonem na mikrostrukturu slitiny AlSi9CuNiMn
Title statement Vliv tepelného zpracování a modifikace antimonem na mikrostrukturu slitiny AlSi9CuNiMn / Roman Skrčený Personal name Skrčený, Roman, (dissertant) Phys.des. 61 listů : barevné ilustrace, grafy + 1 CD Note Vedoucí práce Jaromír Cais Abstract V bakalářské práci jsem se věnoval porovnání výsledné mikrostruktury vzorků slitiny AlSi9CuNiMn tepelně zpracovaných za různých podmínek před a po modifikaci Antimonem. V teoretické části se zabývám základními poznatky o hliníku a jeho slitinách od vlastností přes označování a využití až po rozdělení. Dále všeobecně modifikováním, krystalizací a tepelným zpracováním těchto slitin. V praktické části jsem vytvořil slitinu v požadovaném složení a stejné množství navíc modifikované antimonem. Na těchto dvou základních slitinách jsem dále provedl vytvrzování s homogenizačními teplotami 520, 510 a 490°C vždy s výdrží 1 a 2 hodiny, čímž jsem celkem získal 12 vzorků po tepelném zpracování a dva původní. Následoval proces umělého stárnutí při teplotě 170 °C po dobu 4 hodin. Všechny získané slitiny byly porovnány pomocí mikroskopické analýzy a podrobeny měření mikrotvrdosti, aby byla potvrzena či vyvrácena myšlenka, že v daném podniku lze snížit teplotu homogenizačního žíhání z 520 na 490°C beze změny vlastností materiálu. Výsledkem je zjištění, že tuto teplotu lze snížit. In my bachelor thesis I focused on comparing the resulting microstructures of the alloy samples AlSi9CuNiMn that were thermally treated under different conditions before and after the antimony modification. The theoretical part deals with fundamental knowledge of aluminum and its alloys from the properties through the use of labeling and its division. Furthermore, this part deals with modification, crystallization and heat treatment of these alloys. In the practical part I have created the alloy with desired composition and the same amount of this composition modified by antimony. On these two basic alloys I further performed hardening with homogenization temperatures of 520, 510 and 490 ° C, always lasting 1 and 2 hours, thereby I obtained total of 12 samples with heat treatment and two original. This was followed by process of artificial aging at 170 °C for 4 hours. All obtained alloys were compared by microscopic analysis and subjected to microhardness measurement to validate or disprove the idea that in the factory the homogenization temperature of annealing can be reduced from 520 to 490 ° C without the material properties being changed. The result of this thesis is fact that this temperature can be reduced. Another responsib. Cais, Jaromír, 1988- (thesis advisor) Another responsib. Univerzita J.E. Purkyně v Ústí nad Labem. Katedra technologií a materiálového inženýrství (degree grantor) Subj. Headings slitiny hliníku * mechanické vlastnosti materiálů * elektromechanické vlastnosti materiálů * tepelné zpracování kovů Subj. Headings antimon * modifikace * mikrostruktura * silumin * vytvrzování * antimony * modification * microstructure * hardening Form, Genre bakalářské práce Conspect 620.1/.2 - Nauka o materiálu UDC 620.2-026.56 * 620.2-026.661-026.56 * 621.78 * 669.715 * (043)378.22 Country Česko Language čeština URL https://portal.ujep.cz/StagPortletsJSR168/CleanUrl?urlid=prohlizeni-prace-detail&praceIdno=00170212 Document kind Diploma theses Call number Barcode Sublocation Volný výběr Info DA 6962 3300706962 sklad C In-Library Use Only
Number of the records: 1